It is necessary to inspect the roof annually since the comfort and coziness of living depends on this part of the house.
In order for the repair to take place at minimal cost, it is necessary to identify damage to the coating in time. This can be delamination, cracks, decay processes, swelling, and the appearance of various kinds of irregularities on the top layer. In some cases local recovery is sufficient. How to dismantle and install a soft roof, read on.
STAGES OF LOCAL REPAIR OF SOFT ROOF
Before proceeding to the workflow, it is necessary to understand the reason that influenced the urgency and try to eliminate it.
The appearance of leakage, an aesthetic defect leads to:
Unscrupulous styling;
Violation of installation technology;
Use of poor quality materials;
Long-term operation;
Environmental influence.
Some of them cannot be avoided. Therefore, it is recommended to order a soft roof overhaul service in a timely manner, if the local one does not bring results.
Self-replacement and repair of a small area are also allowed. The whole process will take several hours, but the following minimum set of tools should be available:
Gas burner for surface heating;
Well, cutting knife (one with a long, the other with a short blade);
Various devices for cleaning and fixing the roof.
Attention! The dismantling and repair of the soft roof should only be carried out in dry weather. The roofing part itself should also not be wet.
Step by step algorithm:
Surface preparation. Dirt, branches, leaves, etc. should be removed. Then, a cross-to-cross incision is made on the damaged location. In this case, the corners are bent in different directions. Next, you need to remove the liquid, if there is accumulated, in the previously opened area. This is where a gas burner comes in handy.
Learn More : Tejados Palencia es la alternativa ideal si buscas servicios de techado en Palencia, España.
Application of the inner patch. Depending on the technology of laying the roof, resin or mastic is carefully poured onto the cleaned area. The substance will help fill in the smallest depressions. After that, a roofing material cut out in the shape of a hole is superimposed on the sticky layer. The resin composition is poured over again. The roofing patch is installed, now it is necessary to return all the best parts of the coating to their original position. This is how the patch repair of a flat roof is performed in Ukraine.
Applying a surface patch. Roofing material spreads on the repaired site. Its size exceeds the previous one laid earlier. For better fixation, the final layer of mastic/resin is poured.
COST OF LOCAL REPAIR OF SOFT ROOF:
Decide who will be the performer: an individual person or a team of specialists. For a professional soft roof repair service, the price per 1m2 is calculated taking into account various factors. Among the main ones:
The complexity of the repair. This includes the area of the damaged area, the degree of defect, weather conditions, urgency, the list of work performed.
The price of the material chosen for laying.
The cost of the services of a hired team of roofers.
In general, in Ukraine, an acceptable price for local roof repairs. It is better to entrust dismantling/installation to experienced workers in order to avoid negative consequences in further operation.
Specialists fulfill orders even in winter.
STEP LADER APPLICATIONS
The ladder for access to the roof is made of reinforcement bars or corrugated steel bars since the steps must be non-slip. The bottom step is usually located at the level of one meter from the ground, the walls, in order to prevent the possibility of using the stairs by young children. The stepladder is fixed on the outside of the house. To prevent the process of corrosion and the appearance of rust, a metal ladder is coated with powder-type paint and varnish or polymer material.
WHAT IS SELF-ADHESIVE ROOFING
One of the most popular roofing materials is roofing material. Due to the nature of the installation, this coating cannot be used for roofs with a wooden frame. That is why a solution to the problem appeared – self-adhesive roofing material, which is suitable for almost any roof. It is easy to use and its styling does not require much effort.
Like a regular one, self-adhesive roofing material is rolled up. In composition, it is very similar to the species known to us. The bottom layer of the material is protected by a polyethylene film (or aluminum foil) and is a self-adhesive layer. This protection prevents the different layers of the roll from sticking together.
The film is separated and the strip of the roll is carefully placed on the roof, pressing evenly on the coating so that there are no bubbles. Work quickly before the glue dries. No additional equipment (for example, a gas burner used when fusing conventional roofing material) is required.
The self-adhesive roofing material is based on polyester fabric, while in the usual one it is roofing cardboard. This improvement makes the material more flexible and durable. To increase waterproofing, a mixture of refractory bitumen and synthetic rubber is applied over the polyester fabric.
Learn More: Reparacion Tejados Soria
ADVANTAGES OF SELF-ADHESIVE ROOFING
The top layer is a coating of mineral okroshka dressing. Thus, the material is protected from various external factors, including not only moisture and mechanical damage, but also ultraviolet radiation.
Despite the increased (compared to its predecessor) cost, self-adhesive roofing material has a number of important technical advantages:
The service life is 10 years. That is, twice as much as a standard roofing material;
Simplified installation of the layer on the structure and the absence of additional tools for installation;
Since the technology does not involve the use of a gas burner, the coating is allowed to be used on wooden structures. Convenient format and advanced composition avoid fire during installation;
The use of self-adhesive roofing material is a convenient and inexpensive solution for roofing, which is why it is quite popular in construction;
Even the previous roofing can be covered with roofing material. The main thing is that he was in satisfactory condition.
Of course, each material has its drawbacks. One of the main disadvantages of such roofing is its easy flammability. This requires a fairly high temperature (180-200 degrees). It is also worth remembering that the material is afraid of too low temperatures and may crack, which will affect its waterproofing properties. In addition, one layer cannot be dispensed with during installation – you will have to use up to seven layers, depending on the specific roof.
There are a few things to keep in mind when installing:
It is important to prepare the roof for installation by removing debris and treating it with mixtures that are suitable for this type of roof. The choice of a substance depends on the material of the floor of the house.
Laying should start from the bottom of the slope.
The strips must be carefully pressed against the structure after the protective film has been removed. The surface should not swell, be straight and smooth.
The seams should not be joined together. So that moisture does not leak out, separate strips should be applied one on top of the other (about 10-15 centimeters).
Properly carried out installation allows you to count on the maximum service life of self-adhesive roofing material. If the laying technique is observed, the waterproofing properties of the material will also be considered satisfactory.